Log:

Regency H1529

Téléchargements : 4 Taille : 44 kb    Fabricant : Regency  
Catégorie : Cheminées

Consult your local distributor for fireplace code information. Printed in U.S.A. © 2004 by LHP P/N 750,166M REV. B 07/2006 LHP 1110 West Taft Avenue Orange, CA 92865

Regency H1526

Téléchargements : 8 Taille : 44 kb    Fabricant : Regency  
Catégorie : Cheminées

The kits contain seven louvers plus one louver with two pre-drilled holes (eight total) and these instructions. INSTALLATION INSTRUCTIONS Step 1. Turn off the fireplace and allow it to cool before proceeding. Step 2. Slightly lift and pull the existing top louver assembly away from the fireplace. Step 3. Slightly lift up the bottom hinged panel to disengage the small hooks on ether side of the panel. Pull forward and lower the panel down to open. Remove the assembly from the fireplace by rem

Regency I3100

Téléchargements : 25 Taille : 94 kb    Fabricant : Regency  
Catégorie : Cheminées

Wood Inserts ^R] EGENCY Wood Inserts FIREPLACE PRODUCTS I3100 Wood Insert I3100 Large Wood Insert Minimum Fireplace Opening Height 25” (635mm) Width 28” (711mm) Depth 17” (432mm) Faceplate Dimensions Standard 44” (wide) x 32” (height) Oversize 50” (wide) x 34.5” (height) Dimension Description I3100 A Adjacent Side Wall (to side) 13” (330mm) B Mantle (to top)** 19” (480mm) C Top Facing (to top) 18” (455mm) D Side Facing (to side) 6-1/2” (165mm) E Minimum Hearth Extension* 16”

Regency Gas Insert E33-LP1

Téléchargements : 12 Taille : 159 kb    Fabricant : Regency  
Catégorie : Cheminées

Please Note: A major cause of chimney related fires is due to a failure to maintain required clearances (air space) to combustible materials. It is of the greatest importance that this fireplace and vent system be installed only in accordance with these instructions. Because of the extreme heat this fireplace emits, the mantel clearances are critical. Combustible mantel clearances from top of the louvers are shown in the diagram below. Mantel may be installed anywhere in the shaded area or high

Regency Gas Insert E33-NG1

Téléchargements : 1 Taille : 159 kb    Fabricant : Regency  
Catégorie : Cheminées

(1.25 kPa) 12” W.C. (2.99 kPa) Manifold Pressure - High 3.8” W.C. (0.95 kPa) 11” W.C. (2.74 kPa) Manifold Pressure - Low 1.1” W.C. (0.27 kPa) 2.9” W.C. (0.72 kPa) Orifice Size -Altitude 0-4500 ft. #31 DMS #50 DMS Minimum Input Altitude 0-4500 ft. (0-1372m) 20,000 BTU/h (5.86 kW) 19,000 BTU/h (5.57 kW) Maximum Input Altitude 0-4500 ft. (0-1372m) 38,000 BTU/h (11.14 kW) 35,500 BTU/h (10.40 kW) Vent Sizing 3” Co-linear 3” Co-linear A C G Approved Venting Systems Flex Vent Systems: FPI A

Regency Direct Vent Medium Gas Fireplace Bellavista B36X

Téléchargements : 2 Taille : 293 kb    Fabricant : Regency  
Catégorie : Cheminées

This versatile fireplace can be installed almost anywhere in your home to provide up to 18,500 BTU of consistent, controllable heat, operating even during power outages. Enjoy multiple styling options: choose sleek flush panels or traditional full screen doors, one of 3 realistic brick styles, or stainless steel inset panels to match your home décor. Specifications Natural Gas Propane Input (BTU) 18,500 17,500 Turn Down to (BTU) 12,500 14,500 EnerGuide Rating* 61.60% 64.32% Efficiency (stea

Regency CANYON C310

Téléchargements : 3 Taille : 360 kb    Fabricant : Regency  
Catégorie : Cheminées

Make sure wood is not stacked directly on the ground, it may absorb moisture from the ground. It should be allowed to dry in these conditions for a minimum of six months, preferably one year or more. IT MUST BE UNDERSTOOD THAT WOOD CANNOT BE LEFT IN ANY KIND OF WET OR DAMP AREA OR IT WILL NEVER BECOME COMPLETELY SEASONED. Your stove will not operate at the level that it is meant to unless you use seasoned, dry wood. Do not burn driftwood or wood that has been in salt water, doing so will void yo

Regency GHC/GRD-5500

Téléchargements : 1 Taille : 367 kb    Fabricant : Regency  
Catégorie : Cheminées

Outside Air Kit B Model No. A B GHC/GRD-5500 in. 36 15 1/2 mm 914 394 GHC/GRD-6500 in. 40 3/4 18 mm 1035 457 Rough Framing Face(Unfinished Shown) Outside Chase Installation Figure 8 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. A Square Housing NotUsed on 5500 Model TYPICAL INSTALLATION SEQUENCE The typical sequence of installation follows, however, each installation is unique resulting in variations to those described. 1. Construct the appliance framing. 2. Route gas supply line to appliance loc

Regency I1200

Téléchargements : 8 Taille : 394 kb    Fabricant : Regency  
Catégorie : Cheminées

Wood Inserts «/REGENCY ^R' FIREPLACE PRODUCTS I1200 Small Wood Insert I1200 Wood Insert Model I1200S Cordwood BTU's 55,000 BTU's EPA g/hr 3.0 g/hr Flue Size 6” (152mm) Unit with Standard Flue Adaptor 9-11/16“ (246mm) 8-1/4* (210mm) Minimum Fireplace Opening Faceplate Dimensions Height 19” (483mm) Standard 3 Sided 38” (width) x 26-1/8” (height) Width 23” (584mm) Standard 4 Sided 38” (width) x 34-1/8” (height) Depth Standard Flue Adaptor 13-3/4” (349mm) Oversize 3 Sided 44” (width

Regency HCD36MH

Téléchargements : 20 Taille : 438 kb    Fabricant : Regency  
Catégorie : Cheminées

If the ashes are to be disposed of by burial in soil or other wise locally dispersed, they should be retained in the closed container until all cinders have thoroughly cooled. SOFTWOOD VS HARDWOOD Softwoods contain about 15 percent highly flammable resin which generates creosote soot in the chimney flue. Burning softwood exclusively may not be as desirable nor as safe as burning denser hardwoods. Many experienced fire-builders use small amounts of softwood kindling and newspaper in conjunction w





catégories