Log:

Woodstock D2483

Téléchargements : 10 Taille : 49 kb    Fabricant : Woodstock  
Catégorie : Autres outils

Load the glue sticks into the back of the gun. 2: Press trigger several times until the glue stick is firmly set into the inner tube. 3: Allow the glue gun to warm up for approximately 5 minutes. 4: Squeeze trigger until glue flows from the nozzle. 5: Glue need not be spread. Press surfaces together within 15 seconds. Use of clamps or other holding devices is not necessary. Clean surfaces for best bonding. 6: Unplug glue gun when finished. No clean up required. Never pull the glue stick out

Woodstock D2485

Téléchargements : 2 Taille : 49 kb    Fabricant : Woodstock  
Catégorie : Autres outils

Load the glue sticks into the back of the gun. 2: Press trigger several times until the glue stick is firmly set into the inner tube. 3: Allow the glue gun to warm up for approximately 5 minutes. 4: Squeeze trigger until glue flows from the nozzle. 5: Glue need not be spread. Press surfaces together within 15 seconds. Use of clamps or other holding devices is not necessary. Clean surfaces for best bonding. 6: Unplug glue gun when finished. No clean up required. Never pull the glue stick out

Woodstock D2258

Téléchargements : 6 Taille : 49 kb    Fabricant : Woodstock  
Catégorie : casques sans fil et autres accessoires

It can either be mounted to a wall or laid flat on a table or bench top. If you are planning to utilize the flashing light feature, it will be most easily visible if it is wall-mounted. The unit should be within 15 feet of the telephone receiver to allow connection of the audio sensor. You will also need access to a 110V outlet to plug in the power transformer. The unit should be located at least 5 feet away from the nearest machine(s). If the machine is too close, the ambient sound from the ma

Woodstock STEELEX PLUS D3206

Téléchargements : 0 Taille : 60 kb    Fabricant : Woodstock  
Catégorie : Perceuses et shuropopverty

Straddle the edge with the nails and twist the drill guide so the nails are stopped on the front and back face of the workpiece. INSTRUCTIONS 1. Locate and mark the center of the hole to be drilled with an awl or center punch. 2. Insert the 3/i6" bushing into the drill guide and insert the Centerpunch/Locator into the bushing. 3. Place the drill guide over the workpiece and center the Locator over the center mark. 4. Without moving the drill guide, remove the Locator and W bushing from the

Woodstock Planer

Téléchargements : 11 Taille : 65 kb    Fabricant : Woodstock  
Catégorie : Avions

Make sure that the knife is at the lowest point of its cutting arc. 4. Note the reading on the dial indicator face. 5. Remove the dial indicator and place it in the same position at the opposite end of the knife. Read the dial indicator again. If the reading is not equal to the first one, adjust one side of the planer bed until the readings are the same at both ends of the knife. Adjusting Bed Rollers 1. Rotate the dial indicator to the “Down-reading” position (see Figure 2). 2. Place the d

Woodstock M1016

Téléchargements : 23 Taille : 73 kb    Fabricant : Woodstock  
Catégorie : Machines-outils

Woodstock SHOP FOX W1752

Téléchargements : 3 Taille : 74 kb    Fabricant : Woodstock  
Catégorie : Machines-outils

Woodstock PAL W1226

Téléchargements : 5 Taille : 75 kb    Fabricant : Woodstock  
Catégorie : Avions

With proper care, the Mini Planer Pal® should provide you with years of reliable knife setting service. Do not try to use these jigs on larger diameter cutterheads since the preset knife height and curvature requirements will not be met. Planer Pal® offers larger, adjustable knife setting jigs for use on larger diameter cutterheads. CAUTION: The zinc coated neo-dymium magnets used in the Mini Planer Pals® are extremely strong, but they are very brittle. To avoid chipping the magnets, rock them

Woodstock SB1039

Téléchargements : 14 Taille : 94 kb    Fabricant : Woodstock  
Catégorie : Machines-outils

Woodstock JOINTER PAL W1210

Téléchargements : 0 Taille : 99 kb    Fabricant : Woodstock  
Catégorie : Avions

A JOINTER PAL® JOINTER KNIFE SETTING JIG INSTRUCTIONS FOR USE Preparation 1. Disconnect jointer from power source. 2. Move the jointer fence all the way to the rear of the jointer table. The fence should be aligned 90° to the outfeed table. The fences on some of the new jointers automatically align themselves when tightened, but older jointers often employ a ‘free floating” fence which should be carefully aligned perpendicular to the outfeed table. Jointer Pal will work without a fence, but





catégories