It is preset at 150 PSI and will not function unless tank pressure reaches 150 PSI. Warning: Do not attempt to adjust or eliminate this safety device. Pump Type: Single Stage Single Cylinder Splash Lubricated Direct Drive: Yes Decibel Level: 69 dba (measured 3 feet from side of pump.) Warranty: One Year Entered Market: 1986 DIMENSIONS Weight: 46 Lbs. Height: 20 Inches Length: 15-3/4" Width: 18-3/4" Output Connection: 3/8" Female Pipe Thread ELECTRICAL Motor: 1 Horsepower Electri

If the motor should overheat, the overload protector will shut the motor off. When the temperature returns to normal, the motor will restart automatically. NOTICE! Do not stop the compressor by pulling out the plug. Use only the On/Off switch, which operates a pressure relief valve on the compressor. If the compressor is plugged in with the switch in the “On” position, the compressor may have trouble restarting against the high pressure which could cause excessive heat build up and could damage

BOSTITCH cannot assume responsibility for product performance if our tools are used with fasteners or accessories not meeting the specific requirements established for genuine BOSTITCH fasteners and accessories. TOOL SETUP The MFN-201 was designed to install 1/2” to 3/4” tongue and groove hardwood flooring. The tool is factory set for 3/4” flooring. Two additional foot plates are included with this tool to accommodate 1/2” and 5/8” flooring. Flooring products will vary and the user must ensure t

Contact your Bostitch representative or distributor with any questions concerning the tool and its use. Bostitch, Inc., East Greenwich, Rhode Island 02818. INDEX Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Tool Specifications: Air Consumption & Operating Pressure . . . . . . . . . . . . . . . 4 Air Supply: Fittings, Hoses, Filters, Regulators . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Lubrication and Cold Weathe

. . . . . . . . . .Replace quick disconnect fittings Worn piston O-ring . . . . . . . . . . . . . . . . . . . . . .Replace O-ring, check driver Tool dry, lacks lubrication . . . . . . . . . . . . . . . . .Use BOSTITCH Air Tool Lubricant Damaged pusher spring . . . . . . . . . . . . . . . . . .Replace spring Low air pressure . . . . . . . . . . . . . . . . . . . . . . . .Check air supply system to tool Loose magazine nose screws . . . . . . . . . . . . . .Tighten all screws Fasteners too short fo

KEEP THESE INSTRUCTIONS WITH THE TOOL FOR FUTURE REFERENCE. IF YOU HAVE ANY QUESTIONS, CONTACT YOUR BOSTITCH REPRESENTATIVE OR DISTRIBUTOR. ANTES DE OPERAR ESTA HERRAMIENTA, TODOS LOS OPERADORES DEBERAN ESTUDIAR ESTE MANUAL PARA PODER COMPRENDER Y SEGUIR LAS ADVERTENCIAS SOBRE SEGURIDAD Y LAS INSTRUCCIONES. MANTENGA ESTAS INSTRUCCIONES CON LA HERRAMIENTA PARA FUTURA REFERENCIA, SI TIENE ALGUNA DUDA, COMUNIQUESE CON SU REPRESENTANTE DE BOSTITCH O CON SU DISTRIBUIDOR. LIRE ATTENTIVEMENT LE PRESENT

ASSEMBLY PROCEDURE FOR SEALS: When repairing a tool, make sure the internal parts are clean and lubricated. Use Parker “O”-LUBE or equivalent on all “O”-rings. Coat each “O”-ring with “O”-LUBE before assembling. Use a small amount of oil on all moving surfaces and pivots. After reassembly add a few drops of BOSTITCH Air Tool Lubricant through the air line fitting before testing. AIR SUPPLY-PRESSURE AND VOLUME: Air volume is as important as air pressure. The air volume supplied to the tool may be

If a wrong fitting is used, the tool can remain charged with air after disconnecting and thus will be able to drive a fastener even after the air line is disconnected possibly causing injury. Do not pull trigger or depress contact arm while connected to the air supply as the tool may cycle, possibly causing injury. Always disconnect air supply: 1.) Before making adjustments; 2.) When servicing the tool; 3.) When clearing a jam; 4.) When tool is not in use; 5.) When moving to a different work are

BOSTITCH SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES. This warranty is limited to sales in the United States and Canada. Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. To obtain warranty service, return th

CAUTION: Do not store tools in a cold weather environment to prevent frost or ice formation on the tools operating valves and mechanisms that could cause tool failure. NOTE:Some commercial air line drying liquids are harmful to “O”-rings and seals – do not use these low temperature air dryers without checking compatibility. 5 LOADING THE N400S EYE PROTECTION which conforms to ANSI specifications and provides protection against flying particles both from the FRONT and SIDE should ALWAYS be worn b