Écrivez votre propre critique du dispositif
Téléchargez votre
Para referencia futura Escriba el numero de modelo y de serie El numero de modelo y de serie se encuentran en el costado del gabinete cerca del panel de control. Use estos numeros en toda la correspondencia o llamadas de servicio relacionadas con su acondicionador de aire. Pour consultation ulterieure Inscrivez les numeros de modele et de serie Noter ci-contre les numeros de modele et de serie (on les trou- ve sur le cote de la grille decorative avant, pres du tableau de commande). Communiquer c
When the thermostat automatically lowered 2 °F every thirty minutes. When the has been rised a total of 4 °F, the thermostat setting at that thermostat has been lowered a total of 8 °F, the thermostat time is maintained until the set time has elapsed, at which setting at that time is maintained until the set time has elapsed, time the air conditioner automatically turns off. at which time the air conditioner automatically turns off. SLEEP timer setting SLEEP timer setting 4 °F 6 °F 8 °F 30 minut
To select SWING Operation Press the SWING button (Fig. 6 T). The SWING Display (Fig. 7 b) will light. In this mode, the Air Flow Direction Louvers will swing automatically to direct the air flow both up and down. To stop SWING Operation Press the SWING button (Fig. 6 T) once again. The SWING Display (Fig. 7 b) will go out. Airflow direction will return to the setting before swing was begun. About Swing Operation During cooling/Dry mode : Swings between 1 and 3. During heating mode : Swings betwe
6 M). Each time the button is pressed, the fan speed changes in the following order: AUTO HIGH MED LOW QUIET About three seconds later, the entire display will reappear. When set to AUTO: Heating : Fan operates so as to optimally circulate warmed air. However, the fan will operate at very low speed when the temperature of the air issued from the indoor unit is low. Cooling : As the room temperature approaches that of the thermostat setting, the fan speed becomes slower. Fan : The fan runs at the
(During operation, it is always ON) • QUIET can't be selected in FAN MODE. • Sleep-timer can't be used. And you can't use both wired remote control unit and wireless simultaneously. (Only one kind can be selected) En-3 Fig. 1 Indoor Unit 1 Operating Control Panel (Fig. 2) 2 MANUAL AUTO button When kept on pressing the MANUAL AUTO button for more than 10 seconds, the forced cooling operation will start. The forced cooling operation is used at the time of installation. Only for authorized servic
En-11 CLEANING AND CARE . En-12 AIRC CLLEEAANNININGG T FHIEL PLASMA TER . En-13 TROUBLESHOOTING . En-16 OPERA TING TIPS . En-17 SAFETY PRECAUTIONS Do not atempto instal this air conditioner byourself. This unit contains no user -serviceable parts. Always consult authorized service per - sonnel for repairs. When moving, consult authorized service personel for disconection tion of the unit. Do not becomexcesively chiled by staying for lengthy periods in airflow . Do not insert fingers or obje
When the forced cooling operation starts by any chance, press the START/STOP but- ton to stop the operation. 3Indicator (Fig. 3) 4Remote Control Signal Receiver 5OPERATION Indicator Lamp (red) 6TIMER Indicator Lamp (green) If the TIMER indicator lamp flashes when the timer is operating, it indicates that a fault has occurred with the timer setting (See Page 14 Auto Restart). 7SUPER QUIET Indicator Lamp (green) 8COIL DRY Indicator Lamp (orange) 9Intake Grille (Fig. 4) 0Front Panel AAir Filter B
About the Program timer To Cancel the Timer Use the TIMER button to select “CANCEL”. The air conditioner will return to normal operation. To Change the Timer Settings Perform steps 2 and 3. To Stop Air Conditioner Operation while the Timer is Operating Press the START/STOP button. To Change Operating Conditions If you wish to change operating conditions (Mode, Fan Speed, Thermostat Setting, SUPER QUIET mode), after making the timer setting wait until the entire display reappears, then press the
If you wish to delete other time settings, repeat steps 2 through 5. Once the setting has been canceled, hold down the SET button for 3 seconds. The WEEKLY display flashes briefly, and then the clock display appears. En-8 TIMER OPERATION (WEEKLY TIMER) To Change Selected Time Settings Press the START/STOP button to stop the air conditioner, and then proceed as follows. Carry out steps 1 to 3 of the “Setting Up the Weekly Timer Operation” procedure to select the day you want to edit. Press the SE