WARNING TOREDUCETHERISKOFFIRE,ELECTRICSHOCK,ORINJURYTOPERSONS, OBSERVETHEFOLLOWING: a. Use this unit only in the manner intended by the manufacturer, If you have questions, contact the manufacturer. b. Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominentwarning device, such as tag, to the service panel. C

Select preferred duct location (vertical or horizontal) if ducting out of kitchen. Refer to page 7 for details. 2. Begin installation by removing the fi lters (if installed) and side spacer panels (36” models only). (Fig 2) 3. Reinforce cabinet with 1”x2” wood strips if additional strengthening is required or if cabinets are framed. 4. Temporarily position the range hood in the desired mounting location. Measure and mark the mounting holes, duct and electrical locations with a pencil. 5. Drill/c

Do not place charcoal filters in the dishwasher or soak them in soapy water. Under normal usage (1 hour per day) filters should be replaced every 3 - 4 months. Charcoal filters may need to be replaced more frequently depending on cooking style. 1. Install metal bracket* onto metal filter from hood by sliding one end of the metal bracket underneath the backside of the gray handle as shown. 2. Push two corner tabs into metal filter frame to lock them in. If pushing tabs is difficult, gently lift

Do not place charcoal filters in the dishwasher or soak them in soapy water. Under normal usage (1 hour per day) filters should be replaced every 3 - 4 months. Charcoal filters may need to be replaced more frequently depending on cooking style. 1. Install metal bracket* onto metal filter from hood by sliding one end of the metal bracket underneath the backside of the gray handle as shown. 2. Push two corner tabs into metal filter frame to lock them in. If pushing tabs is difficult, gently lift

All exhaust must be ducted to the outside. Use Metal ductwork only. Fasten all connections with sheet metal screws and tape all joints w/ certified Silver Tape or Duct Tape. Some Ducting Options: side wall cap w/ gravity damper side wall cap w/ gravity damper Soffit or crawl space Roof Pitch w/ Flashing & Cap 1-5/32” 10-11/16” 5-15/16” 10-5/16”11-13/16” 27-9/16”26-19/32” 5” 9-27/32” 1-1/16” 11-13/16” 4-3/32” 1-1/4” 3-3/4” BACK FRONT C/L 10-5/8” (cut out) 26-7/8” (cut out) = cut out dimension cut

Do not ground to a gas pipe. Check with a qualified electrician if you are not sure the range hood is properly grounded. Do not have a fuse in the neutral or ground circuit. *National Fire Protection Association Batterymarch Park, Quincy, Massachusetts 02269 ** CSA International 8501 East Pleasant Valley Road, Cleveland, Ohio 44131-5575 This appliance requires a 120V 60Hz electrical supply and connected to an individual properly grounded branch circuit protected by a 15 or 20 ampere circuit brea

4 INSTALLATION Ducting Calculation Sheet....................................... 5 Mounting Height & Clearance................................ 6 Ducting Options........................................................... 7 Specifi cations ............................................................... 8 Electrical ......................................................................... 9 Mounting the Range Hood...................................... 10 CBIxxxB and PBI-1100A Internal Blowers.......

DO NOT touch bulb until switched off and cooled. Touching hot bulbs could cause serious burns. Make sure all power is turned off and bulbs are not hot. Remove by turning bulb counter clockwise. Note: Bulb does not unscrew; it turns 60 degrees, stops and falls out. If bulbs are difficult to turn due to prolonged use, firmly attach a glass suction cup approximately the diameter of the bulb or use a rubber/latex glove and turn counter clockwise. Replacement bulbs are available at specialty lighting

E. Watch constantly the fried food in order to avoid the cooking oil fl ares up. F. before performing any mainteinance operation, disconnect the hood from the electrical service. The manufacturers will not to accept any responsability for eventual damages, because of failure to observe the above instructions. - 6 - List of Materials Control Electrical Junction Box Glass Glass Light Bulbs Decorative Mesh Filters Range Hood Body Top Cover TYPE DESCRIPTION N° A M4 1 + 1 B 1/8" x 1/4" 12 C 1/8" x 2/

If you are outside our service area, additional charges may apply for shipping costs for warranty repair at our designated service locations and for the travel cost to have a service technician come to your home to repair, remove or reinstall the Products. After the first year from the date of your original purchase, you are also responsible for all labor costs associated with this warranty. Limitations of Warranty. OUR OBLIGATION TO REPAIR OR REPLACE, AT OUR OPTION, SHALL BE YOUR SOLE AND EXCLU