. . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Equipment Inspection and Storage . . . . . . . . . 1 Final Equipment Inspection . . . . . . . . . . . . . . . 1 Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Power Connections . . . . . . . . . . . . . . . . . . . . . . 2 Engine Start Control Connections . . . . . . . . . 3 Exerciser Option . . . . . . . . . . . . . . . . . . . . .

Check to be sure that oven supports above the Warming Drawer location do not obstruct the required interior 23-1/2" depth and 9-1/4"height. -23-1/4- 10-1/2" -2x4 or 2x2- Runners or Solid Bottom ^-26"— Including Handle Install 2x4 or 2x2 Anti-Tip Block Against Rear Cabinet Wall 9" From Floor to Bottom of Block -30"- Undercounter Installation (In Inches) Note: When installing warming drawer with a cooktop, allow a 2" minimum from cooktop burner box bottom to top of cut-out. Important In

• Preheat prior to use according to recommended times. Food Type Control Setting CrispOpenVent Moisture Selector Setting Bacon HIGH OPEN Bread, hard rolls MED OPEN Fried foods HIGH OPEN Pies, two crusts MED OPEN Pizza HIGH OPEN Potatoes, baked HIGH OPEN Tortilla Chips LOW OPEN Using the Warming Drawer Electric Warming Drawer Temperature selection chart for moist foods To keep several different foods hot, set the temperature to the food needing the highest setting. Place the items needing the hig

Replace side trim by installing the original screws in the FRONT screw holes. • Secure the handle to the door using the REAR screw holes. STEP 3 INSTALL GRILLE PANEL ■ Remove the protective film from the appearance panel. ■ Raise the grille panel to the stop position. ■ Loosen the screws on the side trim behind the frame. Remove the bottom trim. ■ Slide the panel over the metal backer panel and into the trim. ■ If installing Stainless steel panels, first slide the filler panel into the tr

Replace side trim by installing the original screws in the FRONT screw holes. • Secure the handle to the door using the REAR screw holes. STEP 3 INSTALL GRILLE PANEL ■ Remove the protective film from the appearance panel. ■ Raise the grille panel to the stop position. ■ Loosen the screws on the side trim behind the frame. Remove the bottom trim. ■ Slide the panel over the metal backer panel and into the trim. ■ If installing Stainless steel panels, first slide the filler panel into the tr

We’re proud of our quality products and we believe in dependable service. You’ll see it in this easy-to-use manual and you’ll hear it in the friendly voices of our customer service department. Best of all, you’ll experience these values each time you enjoy the comfort of your Zoneline. That’s important, because your new Zoneline will be part of your family for a long time. Welcome Staple your receipt to the inside back cover of this manual. You will need it to obtain service under warranty. Writ

Loose fitting or hanging garments should never be worn while using this appliance. Read and follow this Safety Information carefully. SAVE THESE INSTRUCTIONS Features of Your Warming Drawer Electric Warming Drawer Design information (Not all features are on all models. Appearance may vary.) 4 3 5 2 1 6 Feature Index Page 1 Warming Drawer 11 2 Moisture Selector (on back of panel) Use this to keep foods moist or crisp. 7, 9, 10 3 Control Knob The control knob has settings for PROOF, LOW, MED and H

The cutout depth must be 24". The refrigerator will project forward, slightly beyond adjacent 194Dia4 cabinetry, depending on your installation. The cutout depth beneath a soffit: When installed beneath a soffit, the soffit cannot exceed the 24" installation depth shown. The top case trim overlaps the bottom of the soffit. Frameless cabinets: The case trim overlaps cabinets at the top and sides. Therefore, frameless cabinets may require filler strips to prevent interference with cabinet door swi

Note: the top case trim at the front is 1/2" higher and will overlap upper cabinetry or soffit. Use leveling legs and wheels for a maximum 1" height adjustment. Product Clearances These units are equipped with a 2-position door stop. The factory set 130. door swing can be adjusted to 90. if clearance to adjacent cabinets or walls is restricted. Order WX14X99 door stop for precise settings between 90.and 130.. 25" Minimum to Wall 130.Door Swing Corner Installation 90.Door Swing 23-7/8" Behind Fra

Additional cutout width may be required when side panels are used. Add side panel thickness to the finished cutout to calculate rough-in width. • The water and electrical locations for each product must be located as shown. • A separate 115V, 60Hz., 15 or 20 amp power supply is recommended for each product. 25" Min. to Wall 0" 25" Min. to Wall130.Door Swing 130.Door Swing Clearances for two products installed side-by-side with right and left side hinges together Clearances for Multiple Single Do