Connect the power cord to the auxiliary power outlet on the rear panel of your amplifier or receiver or to a household AC outlet. 2. Connect the unit output terminals to the PHONO jack of your amplifier or receiver. Output terminals Amplifier (Receiver) L White) L Channel R (Red) R Channel GND (Spade) GND NOTE: Be sure to connect the ground terminal firmly to the amplifier or receiver. If this connection is not made or is loose, a power source "HUM" will result. The major cause of problems in so

During this period, all service and parts necessary to repair a defect will be free of charge. This limited warranty applies to mechanical parts which are subject to wear and tear as specified: • Faders (except P&G fader), specified durability: 15,000 cycles; • Rotary potentiometers, specified durability: 10,000 cycles; • Switches, specified durability: 10,000 cycles. Consequently, the parts listed above are warranted to be free from defects in materials and workmanship for a period of thirty da

UNIT OVERVIEW......................................................................................................................13 DECK A (LEFT SIDE) ...............................................................................................................13 DECK B (RIGHT SIDE) .............................................................................................................13 DECK CONTROLS .......................................................................................

• Adhere to all warnings and security advices, and retain this document for future referenceE aa Install the unit in accordance with the provided instructions P er Supply: O The unit should be connected to a power supply outlet only of the voltage and frequency marked on its rear panel and/or its AC adapterE O The power supply cord should be routed so that it is not likely to be walked on or pinchedE O The power supply cord of the unit should be unplugged from the wall outlet when it is to be un

This will ensure long life and keep a smooth feeling throughout the fader's lifetime. Follow the instructions below to lubricate and clean your faders: REMOVING A FADER: 1. Make sure mixer is powered off and power supply is disconnected from the back of the mixer. 2. To remove the lower faceplate, take off all the fader knobs and then remove the 4 screws located on the sides of the mixer (2 on each side). Lift up on the faceplate and it will slide off. 3. Remove the fader to be cleaned or replac

Crossfader Reverse -The crossfader reverse changes the direction of the fade on the crossfader (23). FRONT PANEL FRONT PANEL 25. Crossfader Curve -Controls the taper (fade) shape of the crossfader (23). The crossfader curve control continually adjusts the curve from a sharp cut to a long fade. 26. Headphone Outputs -1/4” and 1/8” connector jacks for headphones. BACK PANEL BACK PANEL Power -Power switch to turn the mixer “ON” or “OFF”. AC IN: This is the input connection for the included power su

7. Booth level control: Controls the signal level of the booth output. 8. Headphone level control: Controls the overall headphone output level. It is recommended headphones with an impedance rating of 200 ohms or less be used for maximum volume. 9. Headphone output: Connection for 1/4 inch headphone. Recommended headphone impedance is 32-200 ohms for maximum volume. 10. Cue pan: Fades the headphone output between the channel(s) selected by the cue assign switches (15) and the master one output,

x 8.66 in. x 4.72 in. (48 cm. x 22 cm. x 12 cm.) 4.5 kg (9.9 lbs) Congratulations on your choice of the Stanton RM-22 Professional DJ Mixer. You now own one of the most flexible DJ mixers ever designed. The rackmountable RM-22 offers up to three Microphone inputs, three Phono inputs and nine Line inputs—making it one of the most powerful DJ mixers around. And with Stanton’s smooth fader movement and rock-solid reliability, it’s the perfect mixer for mobile and club DJs alike. Please take a momen

Check all input and output connections for s e c u re fit. Isolate and re p l a c e the damaged cable. Pro g ram volume canOt be adjusted with master vo l u m e c o n t ro l . No powe r. Amplifier or outboard gear connected to the re c o rd output. I m p roperly connected AC cord or power line source not on. B l own fuse. Connect amplifier or outboard gear to master output. Properly connect AC cord to AC power source. Turn powe r o n . Re m ove the fuse cover with a flat-bladed scre wd r i ve r.

A Mains plug with fuse and voltage selector. Changing the fuse: The lid for the housing of both fuses can easily be opened by pressing both sides of the lid simultaneously. After changing the fuses, please make sure the lid is closed securely. To switch the voltage selector it is also necessary to open the fuse housing. You must now twist the plug to the desired voltage setting. The selected voltage can be seen from outside. Make sure to replace the fuses with the necessary value, as indicated o