For a safe operation of the trimmers it is important, that the knife guard is not taken off. The knife carrier (#3) is fitted with a friction device. If adjusted correctly, this friction device insures, that the knife carrier (#3) with the knife cannot move down on its own from any position. If the blade and blade carrier fall by themselves the friction device must be adjusted as follows: For the model 1038 loosen the set screw (I). Tighten the lock nut (II) and retighten the set screw (I). F

abcoffice. com (800) 658-8788 Models 112, 115, 118, 124 6 2 Thank you for selecting Dahle to be your Paper Cutter company. We trust you will be thoroughly satisfied with your purchase. Dahle cutters are highly regarded world-wide for their precision, reliability, and durability. In addition, all Dahle cutters are individually tested and must meet the most stringent performance standards. During use, please observe the following suggestions for care, maintenance and proper operations: • Y

In addition, the cutting board is printed with V2“ grid lines (#2), which acts as an excellent visual aid in achieving a straight T-square cut. • Insert the material to be cut under the clamp/safety guard (#3). • Align material at desired position on inch/cm scale (#1). Material should be flush with paperstop (#4), and parallel to the printed grid lines (#2). • Depress the material to be cut with the clamp. The clamp will secure the material in position, preventing slippage. While clamping th

If it moves too easily, it can be adjusted with the bolt assembly located at the fulcrum (#9). In order to do so, remove the screw (#5) first and take off the lid (#6). Then tighten the hex nut (#7) and the screw (#8) in a counter-action, thus adjusting the pressure of the upper blade against the lower one. At last put the lid back on and secure with the screw. Cutting Board Surface - The cutting board should be cleaned periodically, or as often as required, in order to retain it’s original lus

A mild general household cleaner is recommended. LUBRICATION The blades of your Dahle cutter were lubricated at the factory and do not require any additional treatment. Do Not lubricate the cutting blades. CAUTION • Keep fingers clear of cutting blades. • Do not lubricate the cutting blades. • Keep out of reach of children. • Keep handle in down position when not in use and when moving or transporting. a bcoffice (800) 658-8788 12112.90.1830 - 7/00

To release the upper blade gently push to the right approximately ^” and lift up. • Place the matD backstop to the correct position. • Press the blade down slowly. The clamp will then automatically hold the material to be cut in place. • After the cutti to the right ^”, dropping the blade down slightly and then pushing the handle slightly back to the left. If you have any questions, please call a Customer Service Representative at (800) 658-8788. P9D4HLE abcoffice (800) 658-8788

These high quality cutters have been carefully engineered to provide years of service with a minimum of maintenance. Dahle Cutters use only the highest quality Solingen Steel blades, ground and tempered to exacting standards. Each cutter has been carefully assembled and tested to meet Dahle’s highest standards. For more information about Dahle products contact ABC Office at 1800-658-8788. WARRANTY NOTE: Unless the Warranty Card is properly and promptly filled out and mailed, you will not be p

This warranty shall not apply to any cutter or part thereof which has been repaired or altered in any way, so as, in our judgment, to affect their reliability or stability, nor which have been subject to misuse, negligence, or accident. THIS WARRANTY is expressly in lieu of all other warranties expressed or implied, and the manufacturer neither assumes or authorize any representative or other person to assume for it, any other liability in connection with sale, maintenance, or repair of said cu

The Cutter Blade should open and close without binding. HOLD DOWN SYSTEM The material hold-down system should be used by applying and holding pressure while cutting. BLADE ADJUSTMENT The Blade is pre-set and should stay in the open position without failing. Should adjustment be necessary, the large chrome lock nut may be tightened until the blade stays up. Do not over tighten. USING THE CUTTER Proper operation of you Cutter is important to fine cuts and long life. This cutter is capable of

To release the upper blade gently push to the right approximately ^” and lift up. • Place the matD backstop to the correct position. • Press the blade down slowly. The clamp will then automatically hold the material to be cut in place. • After the cutti to the right ^”, dropping the blade down slightly and then pushing the handle slightly back to the left. If you have any questions, please call a Customer Service Representative at (800) 658-8788. P9D4HLE abcoffice (800) 658-8788