Because the processor-mounting surface extends above the surface of the cam box on the socket, the heat sink bottom can be flat. The heat sink must have a flat surface of at least 40 mm x 40 mm, centered over the processor. Figure 11 shows the measured thermal performance vs. flow rate for this heat sink. This data represents the expected performance of this heat sink on a dual-core socket F (1207) processor. Based Thermal Design of Custom 2U-4P Systems Chapter 5 32800 Rev. 3.02 August 2006 Ther

To connect an AC97 front panel audio module to this connector, please refer to the instructions on Page 76 about the software settings. HD Audio: AC'97 Audio: 2 1 10 9 Pin No. Definition 1 MIC 2 GND 3 MIC Power 4 NC 5 Line Out (R) 6 NC 7 NC 8 No Pin 9 Line Out (L) 10 NC Pin No. Definition 1 MIC2_L 2 GND 3 MIC2_R 4 -ACZ_DET 5 LINE2_R 6 FSENSE1 7 FAUDIO_JD 8 No Pin 9 LINE2_L 10 FSENSE2 GA-M61P-S3 Motherboard - 24 - English 11) CD_IN (CD In Connector) Connect CD-ROM or DVD-ROM audio out to the conn

1077(a) Responsible Party Name: G.B.T. INC. Address: 18305 Valley Blvd., Suite#A LA Puent, CA 91744 Phone/Fax No: (818) 854-9338/ (818) 854-9339 hereby declares that the product Product Name: Mother Board Model Number: GA-7ZMMC Conforms to the following specifications: FCC Part 15, Subpart B, Section 15.107(a) and Section 15.109(a), Class B Digital Device Supplementary Information: This device complies with part 15 of the FCC Rules. Operation is subject to thefollowing two conditions: (1) This d

• •••• Integrated Peripherals This setup page includes all onboard peripherals. • •••• Hardware Monitor Setup This setup page is auto detect fan and temperature status. • •••• Supervisor password Change, set, or disable password. It allows you to limit access to the system and Setup, or just to Setup. 22 7ZX-1 Motherboard • •••• User password Change, set, or disable password. It allows you to limit access to the system. • •••• IDE HDD auto detection Automatically configure hard disk parameters.

To read the user’s manual of PDF format (readable by Adobe Reader), place the “Driver & Utility CD” into the CD-ROM drive in your system. The auto-run screen will appear, click the “Manual” tab to enter its submenu. If not, browse the root directory of the CD-ROM via the File Manager, and double click the “AUTORUN” file. AMD Socket AM2 ATX Motherboard NB: NVIDIA C51XE SB: NVIDIA MCP55PXE 2GHz HT Dual DDR2 800 DIMM Slots NVIDIA SLI Technology Dual PCI-E X16 Slots Dual GbE LAN IEEE 1394a

All rights reserved. The contents of this document are provided in connection with Advanced Micro Devices, Inc. (“AMD”) products. AMD makes no representations or warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications and product descriptions at any time without notice. No license, whether express, implied, arising by estoppel or otherwise, to any intellectual property rights is granted by this publicati

See Figure 3, "AMD Athlon™ XP Processor Model 10 Power Management States" on page 9. 2. The maximum Stop Grant currents are absolute worst case currents for parts that may yield from the worst case corner of the process and are not representative of the typical Stop Grant current that is currently about one-third of the maximum specified current. 3. These currents occur when the AMD Athlon™ system bus is disconnected and has a low power ratio of 1/8 for Stop Grant disconnect and a low power rati

AMD Athlon™ XP Processor Pin Diagram— Bottomside View Chapter 11 Pin Descriptions Preliminary Information AMD Athlon™ XP Processor Model 10 Data Sheet 26237C—May 2003 Table 23. Pin Name Abbreviations Abbreviation Full Name Pin Abbreviation Full Name Pin A20M# AE1 KEY AA7 AMD AH6 KEY AG7 ANLOG ANALOG AJ13 KEY AG9 CLKFR CLKFWDRST AJ21 KEY AG15 CLKIN AN17 KEY AG17 CLKIN# AL17 KEY AG27 CNNCT CONNECT AL23 KEY AG29 COREFB AG11 NC A19 COREFB# AG13 NC A31 CPR# CPU_PRESENCE# AK6 NC C13 DBRDY AA1 NC E25 D

Resolution Status. Fix planned for a future revision. Preliminary Information AMD Athlon™ Processor Model 6 Revision Guide 24332E—December 2002 17 Deadlock May Occur in a Two-Processor System in the Presence of Probe to Memory- Mapped I/O Products Affected. A0, A2, A5 Normal Specified Operation. Processor should not hang. Non-conformance. In a multiprocessor system, if one processor (A) is continuously writing to a cacheable memory-mapped I/O block while the other processor (B) is trying to read

It is a mature architecture that is designed to extract greater performance potential from multiprocessor systems. As developers deploy more demanding workloads on these multiprocessor systems, common performance questions arise: Where should threads or processes be scheduled (thread or process placement)? Where should memory be allocated (memory placement)? The underlying operating system (OS), tuned for AMD Athlon 64 and AMD Opteron multiprocessor ccNUMA systems, makes these performance decisi