With a 1/8” wrench, adjust all four studs by tightening the lock nuts (Figure 28), then loosening them 1/8 to 1/4 turn. If the lock nuts are set too tight, height control will not operate easily. If the lock nuts are too loose, excessive deflection of the outboard end of the drum carriage will result. 2. Apply lubricant to front and rear areas of motor mount slide. 3. Push height adjustment handle (Figure 28) downward to set firmly on housing. Figure 27 Figure 28 18 4. Loosen set screws on colla

A good rule of thumb when sanding with grits finer than 80 is lower the drum so that it contacts with work piece but still can be rotated by hand. When using grits coarser than 80 grit, you can lower the drum slightly more. However, a combination of several variables will determine the proper depth of cut to use, including the following: • Abrasive type and grit size. • Width of the piece being processed. • Hardness of the piece. • Feed rate of stock. Establishing the Proper Drum Height To estab

Slide cross bar toward outboard side as shown. 4. Loosen v-belt tension by loosening pinch bolt in motor support (Figure 38) and raise motor. Remove v-belt from pulleys. 5. Install new v-belt and tension the belt by using the weight of the motor only. Make sure the pulleys are aligned. Replace transfer rod and miter gear; tighten set screw on miter gear and replace protective cap. Tighten collar on transfer rod. 6. Install the outer half of the belt guard and tighten the six screws. Rotating Dru

That means consistent performance with minimal adjusting by the operator. The drum is equipped with patented abrasive take-up fasteners that make changing the abrasive strips fast and easy. We also include our exclusive Tuf Tool™ that makes operating the take-up fasteners a no-strain event. Table and Feed The expansive conveyor surface is expanded even further with the included steel extension tables. (left) Easy to use conveyor belt tension adjusters (right) even have the necessary wrench captu

Level with the Saw Table 1. Place the fence on the table and lock it. 2. View the fence from the left side of the saw. Look for the space between the table and the fence bottom to be equal along the entire length of the fence. 3. If adjustment is necessary, unlock the fence. 4. Raise or lower two nylon adjustment screws (A,Fig.4) the same number of turns until the space between the bottom of the fence and the table is the same. Care must be taken to raise or lower the fence on each side equally

91-603 The Gold Standard Since 1921. POMMMIVC

Tools Required for Assembly & Adjustment 1 #3 Cross Point Screwdriver 1 7/16” Wrench 1 1/2" Wrench 1 Combination Square & Straight Edge 1 Electric Drill 1 1/4”, 3/16” Drill Bits 2 4”-6” C-Clamps 1 1/4”, 3/16” Allen Wrenches 3 Assembly Note: To insure that you have enough adjustment in the cursor during the final adjustments, at this time you should bolt the guide rail to the front rail with two hex cap screws. Place the fence on the guide rail so that the cursor lines up at four inches. Measure

POWERFUL. PRECISE. Quick, tool-1 ess assembly Rigid, ligOt weight fram e • Quick install filter and collection bags • Large wheels for mobility • 500 CFM performance for efficient dust collection • 30 Micron Filtration for cleaner air 4" Dust collection hose provided • Sight window in lower collection bag SPECIFICATIONS Stock Number 708660 Model Number DC-500 Net Weight (lbs.) 65 Gross Weight (lbs.) 75 Blower wheel Diameter(in) 9.5 Sound Rating(dB) 65 1 -Hose connections diamater(i

The indexable carbide inserts make blade changes easier than ever before. Extra long cast iron beds allow for more accurate flat edges and faces on your material. The paddle style power switch can be mounted either below or above the infeed table; while the front mount handwheels make table adjustments easier and more precise. JET 6" HH DELUXE JOINTER Spring-Loaded Blade Guard 56" Long Bed Center-Mounted Fence with Positive Stops Front Handwheels 4" Dust Port 1HP Totally Enclosed Fan cool

POWERFUL. PRECISE. HEAVY-DUTY B3NCH E 8" PLANER/JOINTER If you've got a small shop, or limited space on the job, the new JET® B3NCH 8" Jointer/Planer Combo is right for you. This powerhouse has features usually only found on big floor models. Precision adjustment knobs, compact design, and a powerful 13 Amp motor are only a few features that make this jointer/planer the right choice for wherever you may need it. ID n m — o' . Á A. Large aluminum extruded C. Planing and joining tables E.