Log:

Makita 1002BA

Téléchargements : 36 Taille : 613 kb    Fabricant : Makita  
Catégorie : Avions

A loose installation bolt can be dangerous. Always check to see they are tightened securely. Adjusting depth of cut Depth of cut may be adjusted by simply turning the knob on the front of the tool. Knob Adjusting front base The front base is factory-adjusted to allow concave cuts with a radius of 320 mm. For concave cuts with the tool’s minimum radius of 300 mm, loosen the wing bolt on either side and raise the front base as far as it will go. Then retighten the two wing bolts firmly to secure t

Makita 1050D

Téléchargements : 1 Taille : 135 kb    Fabricant : Makita  
Catégorie : Greeley

Makita 1051D

Téléchargements : 14 Taille : 918 kb    Fabricant : Makita  
Catégorie : Avions

It chamfers up to 5.6 mm (7/32")in a single pass. I groove I I Front base I I ASSEMBLY Dust bag Install the dust bag on the nozzle of the tool. When installing it, push the bag's entry port toward the nozzle as far as it will go to prevent it from coming off during operation. For the best results, empty the dust bag when it becomes about half full. Remove the dust bag from the tool and pull out the fastener. NOTE: If you connect a Makita vacuum cleaner Model 406 to this tool, more efficient and

Makita 1100

Téléchargements : 19 Taille : 893 kb    Fabricant : Makita  
Catégorie : Avions

CAUTION : I Mini planer blade Drum s- \ Groove Bolt Drum - Plarier blade yq Drum cover ' I Adjusting plate Inside edge of gauge plate Blade edge Planer blade Adjusting plate Back side of -- gauge base Gauge plate Tighten the blade installation bolts carefully when attaching the blades to the tool. A loose installation bolt can be dangerous. Always check to see they are tightened securely. For the correct planer blade setting Your planing surface will end up rough and uneven, unless the blade is

Makita 1100(MJ)

Téléchargements : 6 Taille : 88 kb    Fabricant : Makita  
Catégorie : Avions

No. No. Used Description No. No. Used Description 1 911001-2 2 P.H. Screw M3x6 (With Washer) 51 251246-3 4 (+) P.H. Screw M4x5 2 * 2 P.H. Screw M4x14 52 342430-2 2 Adjust Plate 3 911228-4 2 P.H. Screw M5x18 (With Washer) 53 911226-8 2 P.H. Screw M5x18 (With Washer) 4 931106-2 2 Rivet 0-5 54 323001-4 1 Drum Rear Shaft 5 * 1 Switch 55 253139-0 1 Flat Washer 8 6 * * P.H. Screw M4x6 (With Washer) 56 211032-4 1 Ball Bearing 608ZZ (Old 210011-9) 7 682502-4 1 Cord Guard 8-85 57 961004-6 1 Retaining Rin

Makita 18 Gauge 2" Brad Nailer AF505

Téléchargements : 10 Taille : 167 kb    Fabricant : Makita  
Catégorie : Clouteuses

Makita 1805B

Téléchargements : 0 Taille : 701 kb    Fabricant : Makita  
Catégorie : Avions

This is done conveniently with the blade gauge provided. First, remove the blade from the tool by unscrewing the hex bolts. Now, set the Planer blade blade on the gauge blade so that the cut- ting edge is completely flush with the in- side flank of the gauge. Loosen the screws on the adjust plate (if they are not already so) and use the back of side plate to push the heel of the planer blade into full con- tact with the gauge inside flank. Holding it thus, tighten the 2 screws on the adjust ' \

Makita 1806B

Téléchargements : 105 Taille : 131 kb    Fabricant : Makita  
Catégorie : Avions

should never be left around the work area. 7. Before using the tool on an actual work2. Avoid cutting nails. Inspect for and piece, let it run for a while. Watch for remove all nails from the workpiece before vibration or wobbling that could indicate operation. poor installation or a poorly balanced blade. 3. Use only sharp blades. Handle the blades very carefully. 8. Make sure the blade is not contacting the workpiece before the switch is turned on. 4. Be sure the blade installation bolts are s

Makita 190

Téléchargements : 13 Taille : 116 kb    Fabricant : Makita  
Catégorie : Avions

Makita 1902

Téléchargements : 68 Taille : 186 kb    Fabricant : Makita  
Catégorie : Avions

alternating current FUNCTIONAL DESCRIPTION 002549 1 1. Knob 002553 1 2 1. Lock button 2. Switch trigger ASSEMBLY CAUTION: • Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. Adjusting depth of cut Depth of cut may be adjusted by simply turning the knob on the front of the tool. Switch action CAUTION: • Before plugging in the tool, always check to see that the switch trigger actuates properly and returns to the “OFF” position when releas





catégories