TO REDUCE THE RISK OF FIRE, FOLLOW THE INSTALLATION INSTRUCTIONS. FAILURE TO FOLLOW INSTRUCTIONS MAY RESULT IN PROPERTY DAMAGE, BODILY INJURY OR EVEN DEATH. CONTACT LOCAL BUILDING OFFICIALS ABOUT RESTRICTIONS AND INSTALLATION INSPECTION REQUIREMENTS IN YOUR AREA. Do Not Discard This Manual: Retain for Future Use 2000970 1/08 Rev. 7 Vermont Castings Intrepid Multi-Fuel Welcome Congratulations on your choice of a Vermont Castings Intrepid Multi-Fuel Heater. With this purchase, you made a commitmen

Damper 7000954 24. Damper Adjuster 7000950 25. Damper Adjuster Screw 1/4-20 x 1” 1201370 26. Washer 1202561 27. Damper Adjuster Screw Hex Nut 1/4-20 1203212 28. Damper Tab (2) 1601488 29. Damper Crank 7000951 30. Damper Operating Rod 7001145 31. Grate Back 7001166 32. Top 7000960 33. Hearth 7001142 34. Flue Collar 7000969 35. Leg 7000016 36. Damper Handle Stub 5004267 37. Ash Door Handle 5004271 38. Ash Pan 7000G79 39. Gasket for Glass 1203591 40. Glass 7001146 41. Manifold Cap (2) 7001163 42. H

The least clearance is required when both the stove and the wall have heat shields. Reducing a stove clearance may require a listed heat shield on the chimney connector as well, or a double-wall connector. Clearances may be reduced only by means approved by the regulatory authority and in accordance with the clearances listed in this manual. The charts and sample installations that follow list all the clearances required for the various installation configurations of Dutchwest Convection Heaters

Dutchwest noncat cover 5/04 Homeowner’s Installation and Operating Manual If this heater is not properly installed, operated, and maintained, a house fire may result. For safety, follow all installation, operation and maintenance directions. Contact local building officials about restrictions and installation inspection requirements in your area. SAFETY NOTICE Non-Catalytic Convection Heater Model 2478 Dutchwest Non-Catalytic Convection Heater The Dutchwest Model 2478 covered in this Owner’s Gui

If the paint needs retouching, allow the stove to cool completely. Wire-brush areas needing to be painted. Remove non-painted components such as air controls or cover them with masking tape. Touch up the stove with high temperature stove paint available from your local dealer. Apply the paint sparingly. Two light coats are better than one heavy one. Cleaning the Glass Maintenance ST806 Fig. 30 Door latch adjustment. Small Locking Nut Pawl Striker Screw Door Large Lock- ing Nut You will find that

• Inspect for and remove ash build-up behind the combustion package. This should be done in conjunction with annual cleaning of the chimney connector since this inspection is most conveniently done through the flue collar opening. Inspect the passages to either side of the combustion package (a mirror will be helpful) and vacuum away ash using a flexible vacu30002291 25 26 Dutchwest Non-Catalytic Convection Heater 30002291 um hose inserted into each passage. Care should be taken not to damage th

3 continued... Usecautionwhenopeningthedoorofthesmokerwhileinoperation.Keephands,face,andbodysafefromhotsteamorflare-ups.Protectyournoseandmouthfromsmokeinhalation. DONOTwearlooseclothingwhileoperatingthesmoker.Tiebacklonghairwhileoperatingthesmoker.ALWAYSwearfully-coveringshoeswhileoperatingthesmoker. Allowthesmokeranditscomponentstocoolcompletelybeforeconductinganyroutinecleaningormaintenance. NEVERuseglassware,plastic,orceramiccookwareonorinyoursmoker. NEVERoperatethesmokerwithoutwaterinthewa

2.Besureallthetabsonthebacksideofthecontrolpanelarecapturedaroundthelegsasshownbelow. 3.Insertthetworemainingboltsandtightenthemsecurely. 8 Assembly Step 4 Locate these parts: Burner Assembly Tools needed: Phillips Head ScrewdriverHardware: HARDWARE BAG B 1/4-20 x 1/2” Bolts 3 Required 1.Settheburnerassemblyontothecabinetasshown.IMPORTANT:Theburnertubemustslideproperlyontothevalvestemasshownbelow. 2.Securetheburnerassemblywiththethreeboltsfromtheinsideofthecabinet.Securelytightenthebolts. 3.Atta

—Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. —WHAT TO DO IF YOU SMELL GAS • Do not try to light any appliance. • Do not touch any electrical switch; do not use any phone in your building. • Immediately call your gas suppler from a neighbor’s phone. Follow the gas suppler’s instructions. • If you cannot reach your gas supplier, call the fire department. Installation and service must be performed by a qualified installer, servi

The RUVSOD model incorporates variable regulators that allow you to adjust burner heat output between HIGH, (35,000 BTU), and LOW, (26,000 BTU). See the Operation Section for details. A push button Piezo ignitor is used to light the standing pilot. The pilot incorporates an Oxygen Depletion System (ODS/pilot) which will shut off gas flow to the burner in the event that sufficient fresh air becomes unavailable for continued safe operation. Fresh Air Requirements for Combustion and Ventilation WAR