NOTE: The tamper-resistant pin will have to be removed in order to change the battery (models 1275CA and PE120CA). Use long nose pliers to pull the pin out of the hole. It is now possible to remove the alarm from the mounting plate. Operation Hush® Control Feature Model 1275CA only: Smoke alarms are designed to minimize nuisance alarms. Cigarette smoke will not normally set off the alarm, unless the smoke is blown directly into the alarm. Combustion particles from cooking may set off the alarm i

. . . . . . . . . . . . . . . . . . . . . . 1 Installation. . . . . . . . . . . . . . . . . . . . . . . . . . 2-12 Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . 13-14 Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . 15-16 Fire Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . 17-20 Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 130 Esna Park Drive, Markham ON L3R 1E3 Consumer Hotline: 1-800-880-6788 w w w. k i d d e . c a Made in China.

• Combustible Gas Indication -Beepsataratethatincreasesalongwiththegasconcentration. • Sensitivity -Producesanincreasingfrequencytonewhensensitivitychangesfromlowtohigh,andproducesadecreasingfrequencytonewhensensitivitychangesfromhightolow. • Dead Batteries -Highfrequencytone,followedbytheinstrumentturningitselfOFF. • Sensor Error -Rapidlychanginghighandlowfrequencytones. Visual Alarm LED • Power ON - Rapidly flashes green during warm- up(approximately60seconds). • Power OFF -Glowsredjustbeforep

A red light on top of the unit flashes whenever a process is complete or when the unit needs attention from the technician. The MAC2000 is ETL listed to UL standards and meets SAE specifications for recycled refrigerant. 1.1 Glossary of Terms A/C Air conditioner or air conditioning A/C System The vehicle’s air conditioning system Unit The MAC2000 itself Screen LCD Display Contaminated Refrigerant that has been mixed with some other type of refrigerant. 1.2 General Operating Guidelines • The MAC2

It will probably be necessary to apply store lubricant to the Cup, revrap, and repeat the procedure several tine» before a satisfactory thin, even filn renains. Do not apply too nuch lubricant or seepage vill result vben TRUE-SPOT is stored. After Cylinder bore is lubricated; vork lubricant renaining on uuslin cloth onto outer rim of Cup and reassemble TBDE-SPOT. Parts List for TRUE-SPOT® Smoke Tester (21-7012) 1. laeberaeh Xaeorporete4 nrrati to btjw thet at fib* tiae of 4«livery this ptoSe

Replace filter as necessary by first pulling off the filter chamber’s top cap and then exchanging the filter with a new one. Condensate Pump WARNING! The condensed water will be warm and slightly acidic. Take all necessary precautions to prevent the water from splashing into your eyes or contacting your skin. Empty the pump’s reservoir (Figure 3, Item 15) by first holding the pump with its reservoir facing downwards. Then twist the reservoir 90 degrees (either clockwise or counterclockwise) t

5 - June 2005 Introduction The Bacharach Flue-Gas Sample Conditioning System consists of the following components: • Probe with Peltier Cooler • Condensate Pump with Water Trap • Power Supply The function of this system is to remove water vapor from the flue-gas sample, thus preventing the formation of water droplets inside the probe hose. If water droplets were to form inside the hose, a portion of the gas sample could be absorbed by the water, thus resulting in lower-than-actual readings

1. Before running the self test, make sure there is sufficient paper to run the test (18" [46 cm]); the paper cover is closed; and that the printer is switched OFF. 2. Press and hold down the FEED pushbutton; then switch ON the printer to begin the test. Note: The test can be aborted by switching OFF the printer. 3. The following typical information is printed, followed by the printer’scomplete character set: Version : 1.1.6 Data bit : 8 bit Parity : None Baud rate : 9600 bps Handshaking : DTR C

The 2800 is based upon the principle of infrared absorption and has two preset alarm levels at 5,000ppm and 10,000ppm. When either of these levels is reached, audible and visual alarm signals are activated, sounding until the CO2 level drops below the preset level. It is the ideal instrument for agriculture, horticulture, nuclear power plants, food & beverage industry and for organizations concerned about indoor air quality. • Compact & lightweight • Rapid detection of changing CO2 levels • M

It measures in 5 PPM increments and features both PPM and TWA measurement capabilities, which can be accessed with just a touch of a button. Two modes of TWA are available - real time (over 8 hours) and elapsed time (time unit is switched on). A built-in data- logger provides traceable readings for record keeping purposes. The N2O Monitor 3010 also includes an internal sampling pump. And, it is not necessary to span or calibrate the monitor -zeroing in fresh ambient air or with nitrogen is all t