1.0 Sep. 2002 COPYRIGHT 1994-2002 Eurotech S.p.A. All Rights Reserved. PC/104-Plus – COM-1460 Module ABOUT THIS MANUAL This manual is meant for engineers and programmers who wish to develop systems based on the Eurotech COM-1460 PC/104-Plus module. It contains the module’s technical specifications, and describes the connections and firmware/software. It also describes how to install, configure and troubleshoot the COM-1460 module. Via J. Linussio 1 33020 AMARO (UD) ITALY Phone: +39 0433 485 411

CONTENTS IMPORTANT SAFETY INSTRUCTIONS ..................................................... 3 DESCRIPTION OF THE MACHINE ............................................................ 4 INSTALLATION INSTRUCTIONS ............................................................... 5 INSTRUCTIONS FOR USING THE TUMBLE DRYER ............................... 8 CARE LABEL INSTRUCTIONS .................................................................. 9 THE CONTROL PANEL ......................................

This continues until the door is opened or the program knob is turned to the 12:00 position. COOL-DOWN Every program ends with a cool-down cycle that is designed to reduce wrinkling. This means the clothes will be cool when you remove them from the dryer, rather than scorching hot. After the cool-down cycle ends, the light flashes and an end-of-program tone sounds to indicate the program is complete . ANTI-CREASE If the knob is not turned to the 12:00 position or the door is not opened at the en

!. . This usually means a belt is broken. Call a servicer. If you think you have resolved the problem, try starting the machine again. If the problem persists, call for technical assistance (see page 15). BEFORE CALLING FOR SERVICE Before calling for service or contacting AM Appliance Group regarding a warranty issue, be prepared to explain: 1) Model number of the machine 2) Serial number of the machine (located on the inner door facing) 3) Specific problem . 13 NOTES Y MODEL EDV278EL Be su

CONTENTS Important Safety Instructions 3 Child Safety Tips 3 Dishwasher Features 4 Dishwasher Dimensions 4 Installation Instructions 5 Loading the Dishwasher 16 Detergent Dispenser 18 Rinse Aid Dispenser 20 Model EDW132C Operating Instructions 21 Model EDW154E Operating Instructions 22 Model EDW174E Operating Instructions 23 Model EDW194E Operating Instructions 25 Care and Maintenance 27 Overfill Protection 28 Solutions to Common Dishwashing Problems 29 Troubleshooting 30 Washing Special Items 3

A signal will sound to indicate the program has begun and the LCD will display the estimated program run time. If you stop a program in progress by opening the door, you will need to press the Start/Stop button again to restart the program from the interrupted point. INDICATOR LIGHTS The On light indicates that the power to the unit is on. The Rinse Aid light glows when you need to add rinse aid. (See page 20 for instructions on how to load the rinse aid dispenser.) ADDING AN ITEM WARNING! Be ex

to 30-1/16” max. (718 mm–764 mm) (Measured from the top of the panel to the lower edge of the kitchen cabinet.) Thickness: 1/4” (6 mm) minimum to 3/4” (19 mm) maximum Weight: Up to 22 lb. NOTE: Screws for mounting custom wood panels less than 3/4” are not supplied with the unit. MOISTURE BARRIER Among the materials supplied with your unit are two strips of moisture resistant material (moisture barriers). One of these is intended to be affixed along the bottom edge of the back of the wood panel t

Refer to page 27 for information on how to remove these spots. ENGLISH ENGLISHENGLISHENGLISHENGLISHENGLISH 19 RINSE AID DISPENSER Eurotech dishwashers are designed to use liquid rinse aids in hard water areas. The rinse aid dispenser is located inside the door next to the detergent dispenser. The rinse aid is released during the final rinse to prevent water from forming droplets on your dishes that can leave spots and streaks. It also improves drying by allowing water to “sheet” off the dishes.

When moving the appliance into or out of the cabinet, be careful not to damage the power-supply cord. WARNING! Before working on wiring for any electrical appliance, be sure the electrical power has been turned off at the breaker/fuse box. WARNING! Disconnect electrical power supply and place a tag at the disconnect switch indicating that you are working on the circuit. WARNING! Electrical and grounding connections must comply with the applicable portions of the national electrical code and/or o

To restart the appliance, close the door and press the Start button again; the cycle will resume from the point in which it was interrupted. To repeat the same cycle, press the program button and then the Start button. Before you restart the unit, make sure the detergent dispenser is still closed; otherwise, you will have to add detergent. (Please note that if the program has run beyond the fill phase, the water will be pumped out.) Wash Wash Temps (° F) Rinse Temp (° F) Recommended LoadsProgram