The operator may have only two terminals or the numbering sequence may be different. TO CONNECT A THREE-TAB RECEIVER: 1. The push on receptacle on each wire is connected to the straight tab of the receiver terminals. 2. Each terminal is marked on the data label on the back of the receiver. Connect the wires to the receiver terminals as follows: a. Receptacle with two wires (power transformer and push button wire) to terminal mark “1 ” or “24V”. b. Receptacle with second push button wire to

If you have a 3021 receiver be sure to tightly secure the strain K2 N.O. K2 COM. K2 N.C. K1 N.O. K1 COM. K1 N.C. } } relief fitting through which the wires are routed as this Transmitter provides a degree of water resistance. Should you desire 10th Bit Closed a watertight connection, use a single length of 16 to 22 gauge jacketed cable. Transmitter ANTENNA INSTALLATION 10th Bit Open After you have mounted your receiver, test it with the enclosed antenna for range, noting the coverage that you ge

MEAD BOND SIZE: 10.000" x 8.000" SCALE: 1-1) INSTALLATION INSTRUCTIONS Model 2031, 3021, and 3028 2 Channel Receivers WARNING: · Disconnect power before any installation or repair. · Wear safety glasses. Congratulations! You have purchased a MULTI-CODE RECEIVER, which we believe to be the finest product of its kind on the market. If you take a moment to read the enclosed instructions, we think that you will find installation of your receiver to be quite an easy matter, and will assure reliable o

Should you desire 10th Bit Closed a watertight connection, use a single length of 16 to 22 gauge jacketed cable. Transmitter ANTENNA INSTALLATION 10th Bit Open After you have mounted your receiver, test it with the enclosed antenna for range, noting the coverage that you get from all desired operating locations. If greater range or coverage pattern is necessary, you may choose the MULTICODE 1066 Coaxial Wiring Kit, which is available from LINEAR CORPORATION. Note that the external antenna coupli

Check the power connections to the receiver. There must be at least 20 VAC at the receiver power connections. ( If a 24V system) . Review the code switch settings. Any mismatch will prevent the receiver from working. Try a different code switch setting. Check the antenna installation. Wait one minute for the receiver to “ warm- up” . Check battery in transmitter. RECEIVER “ CLICKS” WHEN ANY TRANSMITTER BUTTON IS PUSHED, BUT NOTHING ELSE HAPPENS. Check the wire & connections in the STOP circuit.

INSTALLER: Leave this manual with your customer upon completion of the installation. Page 1 of 4 P/ N 190-104780 REV D Page 2 of 4 P/N 190-104780 REV D IMPROPER WIRING COULD CAUSE ELECTROCUTION OR DAMAGE TO CIRCUITRY. FOLLOW LOCAL BUILDING AND ELECTRICAL CODES. WARNING WARNING DO NOT USE RADIO CONTROLS ON COMMERCIAL DOOR OPERATORS UNLESS PROPER ENTRAPMENT PROTECTION DEVICES ARE INSTALLED. CONSULT THE MANUFACTURER OF YOUR OPERATOR FOR MORE DETAILS. 831 COMMERCIAL RECEIVER WIRING INSTRUCTIONS The

Typically, the AP-1 is used to control a door strike, barrier gate, automatic gate or automatic door operator. The AP-1 contains a high-gain UHF receiver which uses an external antenna to pick up signals from up to 250 feet away. Up to 169 Linear MegaCode Format transmitters and one Model MGT safety edge transmitter can easily be programmed into the AP-1’s memory. The AP-1 will retain its memory, even without power. Two dry contact relay outputs are standard. One relay is the ACCESS RELAY, which

There are no obligations or liabilities on the part of Linear Corporation for consequential damages arising out of or in connection with use or performance of this product or other indirect damages with respect to loss of property, revenue, or profit, or cost of removal, installation, or reinstallation. All implied warranties, including implied warranties for merchantability and implied warranties for fitness, are valid only until Warranty Expiration Date as labeled on the product. This Linear C

10 Wireless Transmitter Programming (Continued) .............................11 System Options .............................................................................12 System Options (Continued) ..........................................................13 System Utilities ..............................................................................14 AE-500 Operation ...........................................................................15 Troubleshooting ............................

PLAN INSTALLATION INTRODUCTION The AM-KP keypad is designed for use with Linear’s AM/II access control system. The keypad is housed in a rugged cast aluminum enclosure. The die-cast keys have bright, easy-to-read yellow graphics. Each key has a positive tactile “click” feel when pressed. An internal sounder signals when a key is pressed. The keypad can be mounted to a pedestal or directly to a wall. A keylock secures the keypad to the mounting backplate. An incandescent panel lamp lights the