Vour machine is designed for long life, dependability, and the top performance you demand. Please take time now to read through this manual so you can better understand the machine's operation, maintenance and safety precautions. Everyone who operates this water pump must read and understand this manual. The time you take now will prolong your water pump's life and prepare you for its safe operation. Enjoy the exceptional performance of your Mustang Semi Trash Series water pump. THIS PUMP CAN P

Consult factory for specific recommendations concerning chemicals and temperatures. 14. Only use original spare parts. 1. Before starting the pumps, follow all of the instructions in this manual and any supplemental instructions supplied with the pump. 1 1. A suction strainer should be attached to the suction hose or pipe. A suction strainer has holes or slots small enough to prevent large debris from working through and damaging the pump. Keep the strainer clean. If possible, suspend the st

Rusting inside engine Refer to Instruction of engine manual 3. Rusting/Sticking of impeller. Disassemble and clean 2. Wrong Direction of rotation. Change rotation direction. 4. Quick coupling gaskets worn, Replace gaskets 6. Priming chamber is over heated. Pour cold water in chamber or let cool. .nqinespëeaSsaôi v.w^E:ijc.!isLwnfiB»cmEàHaK 8. Worn or broken volute or impeller. Replace when necessary. §9^orH|o№ro)^№^^nica№eai 1. Clogged suction hose. Clear obstruction. :raine; 3

Box 1499 Burnsville, MN 55337-0499 1-800-270-0810 NORTH STAR Ranger Pressure Washer HOT- COLD Congratulations on your purchase of the Ranger 157394 Pressure Washer! Your pressure washer is made of high quality components to ensure the top performance you demand. Take the time to read this entire manual so you better understand the machine, how to operate it, the maintenance required and the safety precautions. You will find the assembly, operating, maintenance and troubleshooting instruction

The supply hose should have a 3/4” inside diameter (ID) and be no longer than 50 feet. 2. The water supply pressure must be a minimum of 20 pounds per square inch (PSI) and a maximum of 125 PSI. The flow rate must be at least 3 gallons per minute (GPM). 3. Use a water softener if there is high mineral content in the water of your area. High mineral content causes excessive scale build-up in the coil/heat exchanger. 4. Un-roll the hose reel and then connect one end of the high pressure discharge

Beaverton, Oregon Report # 028-F-59b-5 ANSI Z21.88b-2003 Built-In Direct Vent Fireplace Natural Gas or Propane Residential or Mobile Home WARNING: If the information in these instructions is not followed exactly, a fire or _explosion may result causing property damage, personal injury or loss of life. - Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. WHAT TO DO IF YOU SMELL GAS • Do not try to light any appliance. • Do not

WARNING READ and UNDERSTAND this manual completely before using log splitter. All operators of this equipment must read and completely understand all safety information, operating instructions, maintenance and storage instructions. Failure to properly operate and maintain the log splitter could result in serious injury to the operator and bystanders from moving parts that can crush or cut, flying objects, burns, fire or explosion, escaping high pressure hydraulic fluid, or carbon monoxide poison

Anchor block must be centered on beam and completely welded. 5. Install cylinder onto anchor block with the supplied pin and cotter pins. 6. Log stripper weldment can be welded to the beam or bolted to a 10-gauge (0.1345” thick) plate, which is welded to the beam. If welded to the beam, a 10-gauge spacer must be placed between the log stripper weldment and the beam to get the proper vertical height for the log stripper weldment. The log stripper weldment must rest against the cylinder face to

Depress trigger on gun and drain all water out of gun/lance. RV Antifreeze Funnel Hose Water Inlet Problem Solution Motor will not start SOLUTION: A,B Low/Surging pressure or no water flow SOLUTION: C,D,E,F,G,H No chemical injection SOLUTION: I,J,K,L Cause Solution A- Tripped GFCI cord Reset GFCI cord B- Tripped motor relay Reset motor C- Insufficient water supply See water supply section of this manual D- Plugged pump inlet filter See maintenance section of this manual E- Wrong nozzle Make sure

Always use two hands for safe operation. 10.) Trigger. Actuate to allow pressurized water to flow out of spray gun. *Note: 157301 shown, location of components on other models vary slightly. Pump Component Identification 11 157300 157301 & 157302 FIG02309 Operation Instructions Water Supply 1.) Make sure the water supply is clean. Debris can cause excess pump wear and reduce performance. 2.) An insufficient water supply will damage your pump. Make sure the water supply is steady and is 20% over