• Minimum operational height is 6'-6" (1.98m) to the bottom of backboard. Most injuries are caused by misuse and/or not following instructions. Use caution when using this unit. NOTICE TO ASSEMBLERS ALL Huffy Sports basketball systems, including those used for DISPLAYS, MUST be assembled and ballasted with sand or water according to instructions. Failure to follow instructions could result in SERIOUS INJURY. It is NOT acceptable to devise a makeshift weight system. IMPORTANT! Remove all contents
• When adjusting height or moving system, keep hands and fingers away from moving parts. • Do not allow children to move or adjust system. • During play, do not wear jewelry (rings, watches, necklaces, etc.). Objects may entangle in net. • Keep organic material away from pole base. Grass, litter, etc. could cause corrosion and/or deterioration. • Check pole system for signs of corrosion (rust, pitting, chipping) and repaint with exterior enamel paint. If rust has penetrated through the steel any
Part No. Description 1 1 600002 Tank (Black) 2 1 908213 Top Pole Section 3 1 908144 Middle Pole Section with Label 4 1 908132 Bottom Pole Section 5 4 203099 Nut, Ny-Lock, 5/16-18 6 1 Net 7 1 908217 Pole, Elbow Section 8 1* 203223 Bolt, Carriage, 5/16-18 x 1" Long 9 1 266300 Cap, Tank 10 2 203740 Bolt, Hex, Yellow Dichromate, 5/16-18 x 2.63" Long 11 1 201344 Knob, Plastic, 3-sided 12 1 Rim 13 1 Backboard 14 1 908211 Backboard Mounting Bracket 15 1 908129 Rim Bracket 16 2 203217 Bolt, Carriage 5/1
WARNING 11. 16 4 13 9 4 7 4 10 7 4 10 7 4 16 4 7 4 9 16 4 16 TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN SERIOUS BODILY INJURY AND/OR PROPERTY DAMAGE. WARNING IMPORTANT! Do not over tighten. 14 14 14 1514 13 14 Cut foam stripping (14) to sizes shown and attach to flat side of H-frame (13) as shown. Then secure H-frame to support arms (9 & 10). NOTE: Install H-Frame (13) with foam striping toward backboard. Do this strip last. 11. 16 4 13 9 4 7 4 10
• Check system before each use for proper ballast, loose hardware, excessive wear and signs of corrosion and repair before use. • Check system before each use for instability. • Never play on damaged equipment. • Keep pole top covered with cap at all times. • See instruction manual for proper installation. In the U.S.:1-800-558-5234 and Canada: 1-800-284-8339 201240 2/99 WARNING 37 Crank Height Indicator Hook 201248 2/99 TO ADJUST BACKBOARD: Position looped end of crank onto hook as shown. Rotat
8 10 10 9 9 11 8 8 NOTE: Use existing elevator components. P/N 211540C 12/02 6 printed on recycled paper BRONZE RATCHET ELEVATOR MOUNT (continued) Use existing elevator components. NOTE: Use existing elevator components. NOTE: BRONZE RATCHET ELEVATOR MOUNT (continued) Use existing elevator components. NOTE: Use existing elevator components. NOTE: 7 12/02 P/N 211540C printed on recycled paper STAMPED RATCHET ELEVATOR MOUNT 10 9 9 11 11 8 10 IMPORTANT! Test fit bolts into holes of backboard bracke
Opposite Side View 20 18 19 A. 19 A. Carefully attach cable end to actuator plate (47). 47 19 B. Begin trigger assembly by pulling wire through slot on trigger(48) as shown. Complete this assembly by installing trigger to plates with bolt (53) and bolt (58). 7 42 52 58 66 48 NOTE: DO NOT OVERTIGHTEN NUT (42) ONTO BOLT (58). TRIGGER (48) SHOULD MOVE FREELY. P/N 21166904 10/04 14 20. 20. Slide shroud over strut assembly and attach shroud with screw (60) as shown. 60 15 10/04 P/N 21166904 RIM ASSEM
Secure bottom pole (7) to tank and wheel bracket as shown, a deep socket is recommended. IMPORTANT! DO NOT OVER TIGHTEN. TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. WARNING! 3. 9 8 7Install rod (8) through holes in bottom pole section (7) and eyebolt (9). THE SPACER (11) WILL FIT LOOSELY UNTIL SECURED INTO THE CAVITY OF THE BASE IMPORTANT!: 12 7 8 9 2 11 11 3 3 10 Install wheel axle (2) through wheel carriage (10).
5 4 6 TOP MIDDLE BOTTOM alignment mark alignment mark alignment mark Align poles using alignment marks. First, pound top and middle poles together by bouncing them on a scrap piece of wood on the ground as shown in FIG B. until they no longer move toward pole identification stickers. THEN add bottom pole section and pound together in the same way. middle pole IDENTIFICATION STICKER middle pole IDENTIFICATION STICKER 5" 1-1/2" THE IDENTIFICATION STICKER IS LOCATED 5" FROM THE END OF THE POLE. WHE
Line up holes as shown and tap together. NOTE: Make sure holes remain lined up. Secure poles as shown. ODC (° D 10 10 d 9 13 Attach legs to ple assembly using bolts (8) and nuts (13). Attach rim and board bracket to backboard using bolts (11) and nuts (20). 11 Slide backboard assembly over top pole as shown fully tightening bolts (11) and nuts (20). Secure board by inserting screws (6) as shown. 1 P/N 211745 12/04 2 Toll-Free Customer Service Number for U.S. : 1-800-558-5234 htt