Let the engine cool down sitting on concrete, metal, bare ground or solid wood (e.g. the trunk of a felled tree) away from any combustible substances. Warning! To reduce the risk of fire or burn injury, let the unit cool down before refueling your chainsaw after use. Warning! Never disassemble or modify your muffler. The muffler could be damaged and cause an increase in heat radiation or sparks, thereby increasing the risk of fire or burn injury. You may also permanently damage the engine. H

This rule applies also for those compact saws designed for use in confined spaces. Position the chain saw in such a way that your body is clear of the cutting attachment whenever the engine is running. Stand to the left of the plane of the cutting attachment. A Warning! Do not operate your chain saw with the starting throttle lock engaged. Cutting with the starting throttle lock engaged does not permit the operator proper control of the saw or chain speed. Begin cutting with the saw at full

maam ST/HL021.023.025 Instruction Manual iwner’s Manual Manual de instrucciones Manual del usuario ...» Warning! Read and follow all safety precautions in Owner’s Manual - improper use can cause serious or fatal injury. To reduce the risk of kickback injury use STIHL reduced kickback bar and STIHL PM 1 f/s" Picco) or RM 2 (0.325") chain depending on sprocket pitch or other available low kickback components. ©Andreas Stihl 1993 Advertencia! Lea y siga todas las precauciones de seguridad

If the grip droops to one side: Increase spring tension by one additional turn. 46 021,023, 025 Checking and Replacing Chain Sprocket • When starter rope is fully extended it must be possible to rotate the rotor at least another half turn. if this is not the possible, the spring is over-tensioned and could break. • Take off one turn of the rope. • Fit the fan housing on the engine housing. • Set the Master Control lever to ©t Replacing a broken rewind spring • Lubricate the new spring

If the chain is run dry, the whole cutting attachment will be irretrievably damaged within a very short time. Always check chain lubrication and oil level in tank before starting work. • Every new chain has to be broken in for about 2 to 3 minutes. • After breaking in chain, check chain tension and adjust if necessary -see section "Checking chain tension". 38 021, 023, 025 During Break-in Period During Operation A factory new machine should not be run at high revs (full throttle off loa

1 Assembly Chainsaw assembly and preparation ..............................… 2 Compatible chainsaws and sprockets ……………………… 2 RIPSAW assembly ….........................................................…. 3 Dimension plate assembly …........................................…. 4 Guide beam assembly.......................................….……… 5 End clamp assembly …………………………………………….. 6 Blades Changing blades …..............................................……….. 11 Tracking blades Drive wheel …………………………

Re-install cover knobs and tighten securely. 10. Tighten the tension bolt until the indicator reaches the white line. Refer to chainsaw owner’s manual for the proper oil/gasoline ratio. Maintain an ample supply of bar and chain oil in the reservoir to lubricate the drive mechanism of the RIPSAW. 3 Dimension plate assembly Figure 1. Dimension plate assembly 1. Remove dimension plate and parts from box. 2. Slide guide arm under handle bracket with square pin facing downward. 3. Install and tighten

80 Tooth SaDlina Blade 410.411.4111.4150 8 t 6-8031 Steel Blade Edger Kit 210,211,215,240, 245,310,311,410,2450, 411.4111.4150 9 6-8011 Twin Line Manual Head Kit 240,245,310 410.411.4111 10 6-8108 Comfort Grip Handle Kit 210.310.311 11 6-8045 SDark Arrestor Muffler Kit 410 12 6-8100 .080 R.H. Twin Line (3/8-24 Thd.)Tap Feed Head 212,213,214 13 6-8101 .080 L.H. Twin Line (M10 x 1.25 Thd.) Tap Feed Head 210,211 215.310.311 14 6-8037 .095 L.H. Twin Line Tap Feed Head Kit 210,211 215,310,311

No. 1693706, 1695299 For 54” Mower Decks Instructions Read these safety rules, and the safety rules in your tractor Operator’s Manual, and follow them closely. Failure to obey these rules could result in loss of control of vehicle, severe personal injury to yourself, or damage to property or equipment. THE TRIANGLE SIGNIFIES IMPORTANT CAUTIONS OR WARN- INGS WHICH MUST BE FOLLOWED. WARNING .When blower assembly is removed from the mower deck, the deflector must be properly installed. .If the mowe

NOTE: The following procedure can be performed with the mower installed on the tractor, however for ease of installation, removing the mower deck is recommended Install Hook Plate 1. Remove the right side belt cover and retain taptite screws. 2. Remove the deflector, spring, and hinge assemble. Retain the hardware except for the carriage bolts. Use a hammer to drive the carriage bolts back through the deck, and discard the bolts. 3. Install the hook plate (B, Figure 1) below the stone guard usin