Door back shall be fitted tight within the frame and finished in white. Cabinet shall have butt hinges. Cabinet shall be reversible for left-hand or right-hand installation. MODEL NO. OVERALL SIZE A B C WALL OPENING D E F SHELVES 401ADJ 407ADJ 624 16 20 33/4 16 22 33/4 16 26 41/2 14 18 21/2 14 18 21/2 137/8 237/8 27/8 2 (adj) 2 (adj) 3 (fixed) SURFACE MOUNT CABINET MODEL NO. BODY SIZE A B C OVERALL SIZE D E F SHELVES 614 155/8 195/8 35/8 161/4 221/4 41/4 2 (fixed) Broan-NuTone Storage So

Door back shall be fitted tight within the frame and finished in white. Cabinet shall have butt hinges. Cabinet shall be reversible for left-hand or right-hand installation. MODEL NO. OVERALL SIZE A B C WALL OPENING D E F SHELVES 401ADJ 407ADJ 624 16 20 33/4 16 22 33/4 16 26 41/2 14 18 21/2 14 18 21/2 137/8 237/8 27/8 2 (adj) 2 (adj) 3 (fixed) SURFACE MOUNT CABINET MODEL NO. BODY SIZE A B C OVERALL SIZE D E F SHELVES 614 155/8 195/8 35/8 161/4 221/4 41/4 2 (fixed) Broan-NuTone Storage So

Use them individually or together. 1) 1500W heating element provides fast enveloping heat. Efficient fan evenly distributes warm air through room. 2) Exhausts stale air and moisture to refresh the bath atmosphere. • Streamline design with handsome white grille. Grille is tough polymeric, impervious to bathroom climate. • Includes adjustable hanger bars. 16"-24". Built-in junction box with receptacles for simple plug-in of heater and fan motors. • Nickel-chrome heating element. • Quiet poly

Door back shall be fitted tight within the frame and finished in white. Cabinet shall have butt hinges. Cabinet shall be reversible for left-hand or right-hand installation. MODEL NO. OVERALL SIZE A B C WALL OPENING D E F SHELVES 401ADJ 407ADJ 624 16 20 33/4 16 22 33/4 16 26 41/2 14 18 21/2 14 18 21/2 137/8 237/8 27/8 2 (adj) 2 (adj) 3 (fixed) SURFACE MOUNT CABINET MODEL NO. BODY SIZE A B C OVERALL SIZE D E F SHELVES 614 155/8 195/8 35/8 161/4 221/4 41/4 2 (fixed) Broan-NuTone Storage So

Wilhite Street, Cleburne, TX 76031 (1-800-325-8351 REFERENCE QTY. REMARKS Project Location Architect Engineer Contractor Submitted by Date 80D A99044182 B

FEATURES Italian design Island ceiling mount Finish: 304 Stainless Steel #4 Brushed Size: 70cm x 100cm (27-5/8” x 39-3/8”) Ducted telescopic flue accommodates 8’ to 9’ ceilings 8” round duct connector/backdraft damper Halogen lighting (4 x 20 watt, Type JC 12V 20W G4 base Concealed three-speed slide control 900 CFM centrifugal blower Dishwasher-safe filters feature a quick-release latch and polished stainless steel • Heat Sentry™ - automatically turns blower to high speed when excess cooking

• WARNING: To reduce the risk of shock, disconnectpower before servicing. • Not for use in Kitchens. • Acceptable for use over a bathtub or shower wheninstalled in a GFCI protected branch circuit. I M P O R TANT SAFETY INSTRUCTIONS WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: A. Use this unit only in the manner intended by themanufacturer. If you have questions, contact them a n u f a c t u r e r . B. Before servicing or cleaning unit, switch

1. Insert hanger bars in slots provided in housing. 2. Locate fan housing between joists so that the bottom of the housing is even with the planned finished ceiling. Extend the hanger bars to the joists. 3. Use screws or nails (not provided) to secure hanger bars to ceiling joists. INSTALLING DUCTWORK 1. Refer to Figure 2. Place duct collar over flanges at discharge opening of fan. Secure collar by snapping tabs into slots in flanges. 2. Run 4" round duct from outside to fan’s discharge opening.

FAN MUST NOT BE INSTALLED IN A CEILING INSULATED TO A VALUE GREATER THAN R-40. SUITABLE FOR USE OVER TUB OR SHOWER ENCLOSURE WHEN INSTALLED IN A GFCI PROTECTED BRANCH CIRCUIT. FOR BEST RESULTS When installing the Exhaust Fan in a new construction site, install the housing during the rough-in construction. The blower unit and grille should be installed after the finished ceiling is in place. To install the Exhaust Fan in an existing finished building, an accessible area is required above the plan